OLI-CRYL 40.55

TESTING STANDARDS

• DIN EN 71-3 (heavy metals)
• DIN 53160 (resistant to saliva and perspiration) in combination with a colorless topcoat
• DIN 68861 Part 1 B (with selected media), 2-component application
• DIN 68861 Part 1 C (chemical resistance), 2-component application
• Resistant to hand cream
• APEO-free
• Formaldehyde-free
• DINP-free

APPLICATION

Application instructions:

• Optimal application conditions are +20°C and 50% relative humidity.
• Stir the contents of the container thoroughly before removing material.
• Low temperatures slow down or prevent the drying process.
• Mix containers with different batch numbers before use to avoid color differences.
• The hardeners are sensitive to moisture; therefore, reseal the container immediately after removing material.
• For surfaces subject to normal wear, it can also be applied without hardener as a 1K variant. It offers a high-quality alternative to conventional NC color lacquers. In this case, dilute with up to 10% OLI-PUR Thinner V 15.
• Caution: For multi-layer applications, do not switch between 1K and 2K application to avoid possible "lifting". Apply all layers consistently either with or without hardener.
• The respective intermediate sanding should be carried out immediately before the subsequent coating. Alternatively, "wet-on-wet" coating is possible after a short drying time of 20-30 min.
• The application period with hardener 11.4 (MV 10:1) is 8 hours.

Surface preparation:

• The surface must be dry, thoroughly cleaned, and free of oil, wax, grease, silicone, and sanding dust.
• Sand the wood in stages using grit 150/180.
  
• Sand the filler in stages using grit 240/280/320.

Recommended system:

• Prime with OLI-CRYL 40.40 I 1K+2K filler/insulating filler at 150-250 g/m².
• After drying, carry out intermediate sanding using grit 240/ 280/ 320.
• Coat with OLI-CRYL 40.55 I 1K+2K color lacquer at 130 g/m².
• After drying for 20-30 min (wet-on-wet), overcoat with OLI-CRYL 25.50 I 1K+2K multi-layer lacquer, approx. 130 g/m².

Spraying: cup gun

• Spraying pressure: 2.0-3.5 bar
• Nozzle size: 1.6-2.0 mm
• Thinner addition:-
• Viscosity: (4 mm) 70 sec.

Spraying: airless/airmix

• Spraying pressure: 100-150 bar
• Nozzle size: 0.23-0.28 mm
• Thinner addition:-
• Viscosity: (4 mm) 70 sec.

Drying times:

• Dust-dry: 30 min
• Sandable: 2 hrs (2K) / 4 hrs. (1K)
• Stackable: 16 hrs

SAFETY INFORMATION

DANGER

H225 Highly flammable liquid and vapour. H319 Causes serious eye irritation. H336 May cause drowsiness or dizziness.

P102 Keep out of reach of children. P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P240 Ground and bond container and receiving equipment. P243 Take action to prevent static discharges. P271 Use only outdoors or in a well-ventilated area. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

EUH210 Safety data sheet available on request. EUH211 Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist.